• DE
  • DE
    • +49 (0) 2402 766810 info@dyna-mess.de

    DYNA-EVP

    DYNA-EVP
    Technical properties

    DYNA-EVP: Ehra Validation Procedure

    DYNA-MESS Ehra tester for operating load tests on car seats.

    Testing Limits. Elevating Quality.

    Technical properties

    Testing machine for tests according to:

    • EP 84.300.41
    • EP 84.330.21
    • EP 84.332.40
    • EP 84.340.11
    • EP 84.360.40
    • Portal frame with 3 load units (3 front seats or one rear seat)
    • Vibrating plate for vertical movement, with additional horizontal movement
    • Tracking tests (Ehra signal)
    Data sheet

    Software module for tracking tests

    • Setting the curve using an ASCII file
    • Continuous reading and processing by software
    • Set curve can be used for load or displacement control
    • Scaling of the signal through software

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-HAT + DYNA-BDT

    DYNA-HAT + DYNA-BDT
    Technical properties

    DYNA-HAT: Horn Action Tester
    DYNA-BDT: Button Durability Tester

    DYNA-HAT and DYNA-BDT are the ideal products for testing the horn push force and service life of switches on steering wheels.

    Testing Limits. Elevating Quality.

    Technical properties

    DYNA-HAT: Horn Action Tester

    • Actuating the horn
    • Measurement of compressive force and displacement
    • Determining the switching point (on/off)
    • Adjustable electronic load
    • Continuous visualisation of the values

    DYNA-BDT: Button Durability Tester

    • Operating the switches
    • Independent operation of up to 6 stations
    • Adjustable electronic load
    • Visualisation of force and switch feedback (voltage, current)

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-BPS

    DYNA-BPS
    Technical properties

    DYNA-BPS: Brake Pedal System

    The DYNA-BPS torsion testing machine is used for dynamic component testing on electric brake pedals.

    Testing Limits. Elevating Quality.

    Technical properties

    • Function test on electric brake pedals
    • Endurance test on electric brake pedals
    • Testing under climatic conditions
      • Temperature range -40°C to 180 °C
      • Temperature change rate 7 K/min
      • Humidity range 10-98 % r.h.

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-AFT

    DYNA-AFT
    Technical properties

    DYNA-AFT: Automated Foam Tester

    DYNA-MESS has developed the DYNA-AFT (Automated Foam Tester) testing machine for foam testing in accordance with ISO 2439, ISO 3386 and ISO 3385.

    Testing Limits. Elevating Quality.

    DYNA-AFT testing machine for foam

    Technical properties

    DYNA-MESS foam testing

    Foam testing according to standard

    Testing machine for tests according to

    • ISO 2439
    • ISO 3385
    • ISO 3386
    DYNA-MESS DYNA-AFT testing machine for foam
    • Small footprint
    • Test specimen preparation next to test position possible
    • Test at two stations: automatic retraction of the test specimen when the previous test has been completed

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-AST

    DYNA-AST
    Description

    DYNA-AST: Arc Spring Tester

    DYNA-MESS has developed the DYNA-AST (Arc Spring Tester) testing machine for the simultaneous testing of several arc springs.

    Testing Limits. Elevating Quality.

    Description

    • Simultaneous testing of up to 4 springs
    • Torque measurement: Precision measurement for dynamic testing
    • Contactless angle measurement
    • Temperature measurement

    Software module “Fatigue testing on arc springs”

    • Dynamic loading of the springs on block
    • Dynamic tests in angle or torque control

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNAdent

    DYNAdent
    Technical properties

    DYNAdent:
    Testing machine for fatigue tests on endosseous dental implants


    DYNA-MESS offers perfectly customised machines for testing dental implants in accordance with ISO 14801.

    Testing Limits. Elevating Quality.

    Technical properties

    The DYNA1dent and DYNA5dent machines offer a number of advantages over the universal testing machines normally used, which are slightly modified to meet the special requirements of dental testing:

    • Optimised adjustment to fatigue tests according to ISO 14801
    • Purely electric drive, which means: no hydraulics, pneumatics or compressed air required
    • Integrated force measurement, protected underneath the top cover
    • Displacement measurement also protected underneath the top cover
    • Little space required for installation
    • Practical visual display of the operating status (set-up, testing, end of test)
    • Test basin with practical connections for circulation and preparation of the test medium
    • Shear force-free force transmission through sliding joint
    • Sophisticated test software including user administration, sample library, very simple test parameterisation, online graphics, data recording during the entire duration of the test, test protocol
    • Embedding device for straight and/or angled implants

    Other tests can also be carried out by simply changing the test device:

    • 3- or 4-point bending tests on e.g. ceramic rods
    • Bending tests on bridge structures
    • Print tests
    • …
    Data sheet

    DYNAdent in two versions

    DYNA1dent: Single testing machine

    DYNA5dent: 5-station testing machine

    Operation

    DYNAdent is supplied with an all-in-one PC that can be operated both via a keyboard and via the touchscreen monitor.

    Tempering unit

    An appropriate additional device can be installed for temperature control and circulation of physiological saline solution.

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-EndoWear

    DYNA-EndoWear
    Technical properties

    DYNA-EndoWear:
    Universal wear simulator
    for joint implants

    In close co-operation with universities, users and clinics, DYNA-MESS has developed the purely electrically driven wear simulator DYNA-EndoWear. A special feature of this machine is the ability to test both hip and knee implants in accordance with the DIN EN ISO 14242-1 (hip) and 14243-3 & 14243-1 (knee) standards, as well as shoulder and ankle endoprostheses.

    Testing Limits. Elevating Quality.

    Technical properties

    The servo-electric axes are installed in a compact machine that requires only a small footprint. Neither compressed air nor hydraulic oil is required for operation.

    In addition to the three test stations, DYNA-EndoWear has a reference station for load-equivalent conditioning without the influence of wear.

    Another special feature is the synchronised, independent control of the individual test stations using the DYNA-CLC high-performance controller. The proven DYNA-TCC software can be used to quickly and easily parameterise the tests in accordance with the above-mentioned standards.

    Data sheet

    One multi-component transducer measures forces and torques in all six degrees of freedom at each test station. Dynamic loads of Fx=300 N, FZ=3000 N and MZ=10 Nm are possible.

    DYNA-EndoWear is available in three different versions:

    • DYNA EndoWear 3H for tests on hip implants
    • DYNA EndoWear 3K for tests on knee implants
    • DYNA EndoWear 3HK for tests on hip and knee implants

    The implants can also be tested in media (e.g. saline solution) at the individual test stations. Each station is equipped with a leakage sensor and the temperature is set and monitored.

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-EndoK

    DYNA-EndoK
    Technical properties

    DYNA-EndoK:
    Testing machine for knee endoprostheses

    DYNA-MESS testing machine for fatigue tests, tensile and compression tests as well as tests according to various standards and requirements for knee joint prostheses.

    Testing Limits. Elevating Quality.

    DYNA-EndoK testing machine for tests on knee joint prostheses

    Technical properties

    Tests according to:

    • ASTM F1223: Method for determining the range of motion of total knee arthroplasties
    • ASTM F2722: Method for evaluating the mechanical properties of tibio-femoral joint replacement implants for knee prostheses with mobile bearings under torsional loading
    • ASTM F2723: Method for testing the risk of decoupling of knee prostheses with mobile bearings under cyclic anterior-posterior shear loading
    • ASTM F2724: Method for determining the dislocation resistance of knee prostheses with movable discs
    • ASTM F2777: Test method for the determination of mechanical properties and deformation of mobile intermediate discs

    Possible versions:

    • DYNA-EndoK AP: anterior-posterior shear stress
    • DYNA-EndoK R: Rotation
    • DYNA-EndoK APR: anterior-posterior shear stress and rotation

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-BCT

    DYNA-BCT
    Technical properties

    DYNA-BCT: Bike Components Test

    Test stand for bicycle components with two actuators that can be operated together (cradle test) or solo (fork test or seat post test).

    Testing Limits. Elevating Quality.

    Technical properties

    Cradle kick test

    • 2 vertical actuators
    • Connection to pedal cranks
    • Load with 180° phase shift (opposite direction)
    • Seat post free
    • Rigid front fork
    • Rear fork oscillating

    Fork test

    • Actuator horizontal
    • Connection to guided front fork
    • Seat post free
    • Rigid rear fork

    Seat post test

    • Actuator vertical
    • Connection to seat post
    • Front fork guided
    • Rigid rear fork

    Tests according to standard

    • ISO 4210: “Bicycles – Safety requirements for bicycles”
    • DIN EN 15194: “Bicycles – Electric power assisted cycles – EPAC” – City/trekking bikes
    • DIN EN 17404: “Bicycles – Electric power assisted cycles – EPAC” – Mountain bikes
    • DIN 79010 “Bicycles – Transport and cargo bicycles – Requirements and test methods for single and multi-track bicycles”

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC

    DYNA-MBS

    DYNA-MBS
    Technical properties

    DYNA-MBS: Medical Bone Screw

    DYNA-MESS has developed a special servo-electric testing machine for testing metallic bone screws in accordance with ASTM F543.

    Testing Limits. Elevating Quality.

    Technical properties

    Tests according to:

    • ASTM F543: Torsion test
      • Load in moments/angle control with defined rate of rise
      • Determination of yield strength, max. torsional moment, fracture angle
      • Parameterizable fracture detection
    • ASTM F543: Twist-in/twist-out test
      • Turning in and out in angle control with defined speed under axial load
      • Determination of the maximum turning and unscrewing torques
    • ASTM F543: Pull-out test
      • Insertion in angle control with defined speed
      • Axial extraction in path control with defined speed
      • Parameterizable break detection
    • ASTM F543: Self-tapping bone screws
      • Turning in angle control under increasing axial load
      • Determination of the axial force at which the self-tapping effect sets in
    Data sheet

    Always included: state-of-the-art software and electronics

    Software DYNA-TCC
    Electronics DYNA-CLC